Acoustic Silencer for a Dedicated Frequency

Downloads

Authors

  • Adam BRAŃSKI Department Faculty of Electrical and Computer Engineering, Technical of Electrical and Computer Engineering Fundamentals, University of Rzeszow, Poland
  • Edyta PRĘDKA-MASŁYK Department Faculty of Electrical and Computer Engineering, Technical of Electrical and Computer Engineering Fundamentals, University of Rzeszow, Poland

Abstract

Acoustic resonators are useful for damping low frequencies. In cylindrical silencers (mufflers), the implementation of the resonance concept consists in selecting such a length of the expansion chamber (EC) that a wave of opposite phase is created in it, and with this opposite phase the incident wave is damped. Based on the plane wave theory (1D) and simple analytical calculations, it is possible to approximately determine the shortest length of the EC for a selected frequency; such a chamber represents the simplest silencer. Its efficiency is measured by the transmission loss (TL) value; increasing the TL value indicates that the silencer efficiency increases as well. The efficiency was improved in two ways: first, in single EC, by adding inlet, outlet, or both horizontal extensions, and second, by adding another EC. In the first case, the influence of the length of the horizontal extensions on TL was analyzed. In the second study, another dedicated EC was added, and the influence of the width and orifice diameter of the transverse partition on TL was analyzed. All analytical results were confirmed experimentally. The results indicate that, first of all, a simple silencer (single EC) is found to damp a dedicated frequency. In addition, simple changes in the structure of such a silencer significantly increase its efficiency.

Keywords:

acoustic silencer, transmission loss coefficient (TL), expansion chamber (EC), transverse partition, horizontal inlet/outlet extensions to a single D-EC

References


  1. Barron R.F. (2003), Industrial Noise Control and Acoustics, Marcel Dekker, Inc., New York.

  2. Bilawchuk S., Fyfe K.R. (2003), Comparison and implementation of the various numerical methods used for calculating transmission loss in silencer system, Applied Acoustic, 64: 903–916, https://doi.org/10.1016/S0003-682X(03)00046-X

  3. Chaitanya P., Munjal M.L. (2011), Effect of wall thickness on the end corrections of the extended inlet and outlet of a double-tuned expansion chamber, Applied Acoustic, 72(1): 65–70, https://doi.org/10.1016/j.apacoust.2010.09.001

  4. Chang Y.-C., Chiu M.-C., Huang S.-E. (2019), Numerical analysis of circular straight mufflers equipped with three chambers at high-order-modes, Applied Acoustics, 155: 167–179, https://doi.org/10.1016/j.apacoust.2019.05.021

  5. Chiu M.-C., Chang Y.-C., (2014), An assessment of high-order-mode analysis and shape optimization of expansion chamber mufflers, Archives of Acoustics, 39(4): 489–499, https://doi.org/10.2478/aoa-2014-0053

  6. Cui Z., Huang Y. (2012), Boundary element analysis of muffler transmission losses with LS-DYNA, [in:] 12-th International LS-DYNA Users Conference.

  7. Jokandan M.R., Variani A.S., Ahmadi S. (2023), Study of acoustic and aerodynamic performance of reactive silencer with different configurations: Theoretical, modeling and experimental, Heliyon, 9(9): e20058, https://doi.org/10.1016/j.heliyon.2023.e20058

  8. Kang Z., Ji Z. (2008), Acoustic length correction of duct extension into a cylindrical chamber, Journal of Sound and Vibration, 310(4–5): 782–791, https://doi.org/10.1016/j.jsv.2007.11.005

  9. Karami F., Rad M.S., Karimipour I. (2024), Review on attenuation of low – Frequency noise in passive silencer, Journal of Low Frequency Noise, Vibration and Active Control, 43(4): 1679–1695, https://doi.org/10.1177/14613484241228373

  10. Komkin A.I., Mironov M.A., Yudin S.I. (2012), On the attached length of orifices, Acoustical Physics, 58(6): 628–632, https://doi.org/10.1134/S1063771012050090

  11. Lee C.H., Han M.J., Park T.W. (2020), A comparative study on the transmission loss of Helmholtz resonator and quarter, half, conical half-wave resonator using acoustic analysis model, International Journal of Mechanical Engineering and Robotics Research, 9(1): 153–157, https://doi.org/10.18178/ijmerr.9.1.153-157

  12. Łapka W. (2007), Acoustic attenuation performance of a round silencer with the spiral duct at the inlet, Archives of Acoustics, 34(4(S)): 247–252.

  13. Munjal M.L. (1987), Acoustics of Ducts and Mufflers with Application to Exhaust and Ventilation System Design, John Wiley & Sons, Inc., New York.

  14. Munjal M.L. (2013), Recent advances in muffler acoustics, International Journal of Acoustics and Vibration, 18(2): 71–85, https://doi.org/10.20855/ijav.2013.18.2321

  15. Munjal M.L. (2014), Acoustics of Ducts and Mufflers, John Wiley & Sons, New York.

  16. Nilsson E., Vardaxis N.G., Ménard S., Hagberg D.B. (2021), Sound reduction of ventilation ducts through walls: Experimental results and updated models, Acoustics, 3(4): 695–716, https://doi.org/10.3390/acoustics3040044

  17. Potente D. (2005), General design principles for an automotive muffler, [in:] Proceedings of Acoustics 2005, pp. 153–158, https://www.acoustics.asn.au/conference proceedings/AAS2005/papers/34.pdf.

  18. Rafique F., Wu J.H., Liu C.R., Ma F. (2022), Transmission loss analysis of a simple expansion chamber muffler with extended inlet and outlet combined with inhomogeneous micro-perforated panel (iMPP), Applied Acoustic, 194: 108808, https://doi.org/10.1016/j.apacoust.2022.108808

  19. Rahman M., Sharmin T., Hassan A.F.M.E., Nur M.Al. (2005), Design and construction of a muffler for engine exhaust noise reduction, [in:] Proceedings of the International Conference on Mechanical Engineering 2005 (ICME2005), https://me.buet.ac.bd/public/old/icme/icme2005/Proceedings/PDF/ICME05-TH-47.pdf

  20. Selamet A., Denia F.D., Besa A.J. (2003), Acoustic behaviour of circular dual-chamber mufflers, Journal of Sound and Vibration, 265(5): 967–985, https://doi.org/10.1016/S0022-460X(02)01258-0

  21. Selamet A., Ji Z.L, Radavich P.M. (1998), Acoustic attenuation performance of circular expansion chambers with offset inlet/outlet: II. Comparison with experimental and computational studies, Journal of Sound and Vibration, 213(4): 619–641, https://doi.org/10.1006/jsvi.1998.1515

  22. Selamet A., Radavich P.M. (1997), The effect of length on the acoustic attenuation performance of concentric chambers: an analytical, numerical and experimental investigation, Journal of Sound and Vibration, 201(4): 407–426, https://doi.org/10.1006/jsvi.1996.0720

  23. Strek T. (2010), Finite element modelling of sound transmission loss in reflective pipe, [in:] Finite Element Analysis, Moratal D. [Ed.], https://doi.org/10.5772/10236

  24. Swamy M., van Lier L.J, Smeulers J. (2014), Optimisation of acoustic silencer for the screw compressor system, [in:] Excerpt from the Proceedings of the 2014 COMSOL Conference in Cambridge.

  25. Tao Z., Seybert A.F. (2003), A review of current techniques for measuring muffler transmission loss, SAE Transactions, 12: 2096–2100, https://doi.org/10.4271/2003-01-1653

  26. Wei F., Guo L.-X., (2016), An investigation of acoustic attenuation performance of silencers with mean flow based on three-dimensional numerical simulation, Shock and Vibration, 2016: 6797593, https://doi.org/10.1155/2016/6797593

  27. Xiang L., Zuo S., Wu X., Zhang J., Liu J. (2016), Acoustic behaviour analysis and optimal design of a multi-chamber reactive muffler, Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 230(13): 1862–1870, https://doi.org/10.1177/0954407016630112

  28. Yu X., Cheng L. (2015), Duct noise attenuation using reactive silencer with various, Journal of Sound and Vibration, 335: 229–244, https://doi.org/10.1016/j.jsv.2014.08.035

  29. Yu X., Tong Y., Pan J., Cheng L. (2015), Sub-chamber optimization for silencer design, Journal of Sound and Vibration, 351: 57–67, https://doi.org/10.1016/j.jsv.2015.04.022

  30. Zalte Y.B., Sature M.J. (n.d.), Transmission losses in simple expansion chamber of reactive muffler analysis by numerical & experimental method, International Engineering Research Journal, pp. 1933–1939.

  31. Zhang L., Shi H.-M., Zeng X.-H, Zhuang Z. (2020), Theoretical and experimental study on the transmission loss of a side outlet muffler, Shock and Vibration, 2020: 6927574, https://doi.org/10.1155/2020/6927574

  32. Zhao B., Li H. (2022), Analysis of the influencing factors of the acoustic performance of the muffler considering acoustic-structural coupling, Archives of Acoustics, 47(4): 497–490, https://doi.org/10.24425/aoa.2022.142900

Other articles by the same author(s)